However, using an Allen-Bradley motor with your drive removes the . Н Installation guidelines called out in Appendix D of the User’s Manual. Installation Instructions IN. May, Allen-Bradley. Dynamic Brake. Cat. No. KAA KBA03, KBA06, KBA Table of Contents. Find great deals for Allen Bradley Adjustable Frequency AC Drive User Manual. Shop with confidence on eBay!.

Author: Mazugami Teramar
Country: Congo
Language: English (Spanish)
Genre: Education
Published (Last): 15 February 2010
Pages: 185
PDF File Size: 1.59 Mb
ePub File Size: 19.74 Mb
ISBN: 616-8-15456-585-9
Downloads: 65768
Price: Free* [*Free Regsitration Required]
Uploader: Arajinn

Please select the Repairs tab for more information or to request a quote. Check for proper mounting and spacing. Bus overvoltage can also be caused by motor reeneration.

vdd

Allen Bradley Adjustable Frequency AC Drive User Manual | eBay

Reset to Default Parameters and Cycle power. Check for excess load, improper DC boost setting, DC brake volts set too high or other causes of excess current. Check for a short circuit at the drive output or excessive load conditions at the motor. Inspect for proper mounting and spacing.

Phase W Fault – F40 A phase to ground fault has been detected between the drive and motor in this phase. Inspect fault buffer for fault code requiring reset.

Drive Reset Fault – F22 May occur on power-up. Check the motor for grounded phase. Overload Fault – F7 Internal electronic overload trip. Check for broken wires, loose connections, or transducer loss at mA input, TB2. Replace the Communication cable.

  MANUAL CORP 6000 INTELBRAS PDF

If not, manually program any remaining parameters. Reduce [Start Boost] if applicable. Error 4 – Saved data for parameter not correct for new drive. Phase U Fault – F38 A phase to ground default has been detected between the drive and motor in this phase.

No valid operating frequency.

A longer acceleration tiime or a lighter load may be required. Phase V Fault – F39 A phase to ground fault has bradlry detected between the drive and motor in this phase.

1305 AC Drives

Inspect the allej between the drive and motor. Check the motor and external wiring to the drive output terminals for a shorted condition. Overtemperature Fault – F8 Temperature sensor detects excessive heat. Check motor for grounded phase. Hz Sel Fault – F30 An unconnected adapter has been selected as the active frequency source. Inspect for breaks in communications line. Unplug the HIM from the cable or drive and reconnect it. D Micro Programmable Logic Controllers.

The Adjustable Frequency AC Drive is a mxnual speed drive designed to control the speed of three-phase AC induction motors in a variety of demanding applications where flexibility, performance and ease of use are essential. An attempt has been made to set the [Run Boost] parameter to a value greater than zllen [Start Boost] parameter. Press Enter to continue download.

The Adjustable Frequency AC drive is available with ratings 0. Capabilities of drive are different than the master drive.

  GLUTAMINASE THESIS PDF

May occur on power-up. Overspeed Fault – F25 Internal error. Reset your drive to the factory default settings. Open Pot Fault – F9 An external pot is connected and the ground lead of the pot is disconnected, creating a potential drive overspeed hazard. Check for external noise sources.

Error 5 – Drive is running while attempting download Repeat operation. Check the AC line for high line voltage or transient conditions. Verify ,anual the parameter has been programmed correctly. Inspect for short at the drive output or excessive load conditions on the motor, especially cable capacitance to ground.

Check the brad,ey potentiometer circuit at TB2, terminals 1, 2, and 3 for a disconnected current. Unplug the HIM from the cable or drive, then reconnect it. Inspect for blocked or contaminated heat sink fins.

Check mxnual Freq] and [Maximum Freq] parameters. Error 3 – Download was attempted to a different type drive i. Skip frequencies and skip bandwith eliminate all operating frequencies. Serial Fault – F10 An active local bus adapter is disconnected while it possesses control of a local bus function.

Download can only occur with the same type of drive. Connect proper adapter or change active frequency source.