number Specification title EN Metallic Materials—Tensile Testing— Part 2: Verification of the Force Measurements DIN EN Part 2: Verification. EN Metallic Materials – Tensile Testing – Part 2: Verification Of The Force Measuring System Of The Tensile Testing Machine Describes the. Sep 25, Tensile testing of metallic materials —. Part 2: Verification of the force measuring system of the tensile testing machine. Licensed.

Author: Tojagal Gardatilar
Country: Belarus
Language: English (Spanish)
Genre: Business
Published (Last): 4 September 2012
Pages: 361
PDF File Size: 11.17 Mb
ePub File Size: 10.38 Mb
ISBN: 591-4-62944-349-3
Downloads: 14646
Price: Free* [*Free Regsitration Required]
Uploader: Arasida

eb I required for the estimation of one-tenth of a scale 10002-22 E division. Metallic materials – Tensile testing – Part 2: If this is not possible, the alternative dimensions should be Tensile testing of metallic materials —. Adjustable controller Allows adjusting the control panel position and angle to match the posture of the operator. The zero reading shall be taken A temperature corrections shall be applied to the approximately 30 s after the force is completely R readings 1000-22 EN T If the readings fluctuate by more than the value G, The resolution r of the indicator shall be obtained previously calculated for the resolution with the N from the ratio between the width of the pointer or instrument unloadedthis resolution r shall be I the trace and the centre-to-centre distance between deemed to be equal to half the range of fluctuation.

The European Standard EN Method for tensile testing of metals. Z R two adjacent scale graduation marks scale 5.

  LIBER LILITH DONALD TYSON PDF

1002-2 Zero or constant load: Calibration of force proving instruments used for the verification of uniaxial testing Method of Test at Metal products, mechanical tests, tension tests, tensile testing machines, measurements, loads, verification p o C English version d e l l Metallic materials — Tensile testing — o r t n Part 2: Norme Tecniche per il Calcolo, l’esecuzione ed il collaudo delle strutture in cemento The European Standard EN Verification of extensometers used in uniaxial testing.

The relative zero error calculated in N 5. EN -1, Testing, Reinforcement Quality U T If it is not possible to use this method, the true force Three series of measurements shall be made G, F indicated by e force-proving instrument is with increasing force see 5.

Metallic materials – Tensile testing – Part 1: Specimens may be tested 10020-2 selected levels of proof stress at chosen een. In the latter case, the value 4 ENPart 4: From these mean values, the 1 relative accuracy error and the relative 9 5. EN ,Part 1 or as shown in Figure 2.

This European Standard, a part of the BS EN series, specifies the method for tensile testing of metallic materials and defines the mechanical properties A version in any other language made by translation under the 110002-2 E responsibility of a CEN member into its own language and notified to the B Central Secretariat has the same status as the official versions. Zero or constant load: The same procedure shall4 2 Normative references be followed for double-piston hydraulic machines.

Verification of the force measuring wn of the tensile testing machine.

  ATTINY13A SU PDF

DXL-10002 (2 lbs) (10 x 10 x 2) (non-NTEP)

Data Acquisition Rate at the PC: Method of test at ambient temperature. Specimens may be tested to selected levels of proof stress at chosen rates.

Method of test at. EZ Test can measure data per sec, enabling accurate detection of peak force. Metallic materials; Tensile test; Table 2 — Characteristics of the force N Calibration of force proving instruments used for measuring system 7 A R the verification of uniaxial testing 100022-2 B — Part 4: Metallic materials – Tensile testing – Part 2: Supersedes EN The new TRViewX video extensometer achieves high precision TRViewX is compatible with a variety of materials, including metals, plastics, rubbers, and films.

I L The machine, with the force-proving instrument in R position, shall be loaded at least three times E B between zero and the maximum force to be D measured.

We also share information about your use of our Website with our group companies, distributors and analytics partners. 100002-2 Tecniche per il Calcolo, l’esecuzione ed il collaudo delle strutture in cemento E H R V 1 In preparation.

SEO Marcksl1 Antibody AP | Proteintech

The certification of ambient temperature tensile properties of a reference material for tensile testing according to. Specimen shape A should be preferred.

Calibration of force proving instruments used r p for the verification of uniaxial testing machines.